In Windows 10 when you connect the headset, configure the sound output on internal speakers?

The fact that the Jack for microphone and headphone on my laptop (hp envy m6) United. When you connect headphones with embedded microphone, the microphone is working properly, but the sound is output through headphones, and I need the sound continued to be reproduced through the built-in speakers.
Thank you.
June 8th 19 at 17:07
3 answers
June 8th 19 at 17:09
Most often (read always, with rare exception) there physically breaks the contact in the connector ... (!)
or change (customize) connector, or buy a microphone for 60-150 rubles
I have cut off the headphones, leaving only the microphone on the wire. Still the same garbage-) - Reese commented on June 8th 19 at 17:12
, the contact is broken right at the connector, the introduction there [s]phallic symbols[/s] subject matter with a diameter of 3.5 mm (or a little less) - Lurline commented on June 8th 19 at 17:15
that is software and it does not change?-)

Just when I'm changing here https://prnt.sc/i89knd for a couple of seconds the sound switches to internal speakers and then back to headphones - Reese commented on June 8th 19 at 17:18
means there software definition (a built-in feature of AC97 codec), then disable the autodetect in the sound settings of the driver (Choi, I forgot about this thing, a hundred years have not seen :)) - Lurline commented on June 8th 19 at 17:21
To understand where...;) - Reese commented on June 8th 19 at 17:24
the audio icon in the system tray (near the clock) or Realtek or CMI... who else is there now is. Or start from the classic control panel, it's there in one of the categories (you can temporarily turn all the icons to find it) - Lurline commented on June 8th 19 at 17:27
In the system tray generally is not present-)
But in control panel there is a lovely Beath HP Audio, in which there is nothing similar to autodetect-)
https://image.prntscr.com/image/gJ4TryVTTzKaFFpyPB... - Reese commented on June 8th 19 at 17:30
I have the monitor you broke :(

Well, then either do not, or noona to look. Here I not the assistant, I have no such problem, and the setting is there, and the laptop I this in eyes did not see, and even if I did, the memory could hardly tell where and what. - Lurline commented on June 8th 19 at 17:33
okay, thanks for the tip-) - Reese commented on June 8th 19 at 17:36
try a q-tip to insert or Lollipop and see what happens.
Or to find the Pinout of the connector and see may be you can crop the first 2 contacts of the minijack (if there are 4) that you just pressed the contacts which switch off the sound in the speakers. - Lurline commented on June 8th 19 at 17:39
June 8th 19 at 17:11
How many met audiopodcast on the computer - they always detect exactly where the connected speakers or the microphone. One only has to plug the cable and the input/output signal switches to it. Table (and in the old laptop, which sound like the plugin was separate) this is done in the chip mixer purely by electronic means, and in the new laptops, which have a connector only and combined - most probably pure mechanical. If so, nothing to do with the switch will fail. Well, except that to open the laptop, and a soldering iron under a magnifying glass to very carefully short out the contacts when you plug sticking open.
June 8th 19 at 17:13
If you are lucky and your sound card has a recording device, which in real-time to "write" what you hear (a kind of virtual microphone), then everything is simple.
If not, you need to do. For example, so. Seek and ye shall find!
Although some latency problem I could not solve.
And no need to torment Jack. It does not interfere with the output sound wherever your heart desires. It is solely the fault of lazy Windows.

Find more questions by tags Windows