Questions tagged [Hostapd] (15)

1
answer

Adaptor dual band — is it possible?

Purchased Wi-Fi adapter ASUS PCE-AC88 to work as access point (hostapd). Is it possible to configure hostapd to work with this adapter as TWO access points - 2.4 GHz and 5 GHz?
Lonie.Schaden asked March 17th 20 at 13:18
1
answer

How to get out of the mode of distribution of Wi-Fi hostapd?

Once I decided to switch to seeding mode Wi-Fi hostapd. After I can't find an available wifi network. I have to wash and sees the network, but iw is not working. Here is the ifconfig information: wlan0: flags=4163 mtu 1500 unspec -00-00-00-00-00-00-00-00 txqueuelen 1000 (UNSPEC) 112665 bytes RX packets 30651191 (29.2 MiB)...
claud_Osinski asked March 16th 20 at 12:55
0
answer

How to turn off hostapd?

Once I switched to seeding mode hostapd.After I tried to turn it off but could not. Wifi sees the network. But the wash working. Help solve the problem.
Jesus.Bode asked March 16th 20 at 12:53
2
answers

Wi Fi AP Debian

Raised under Debian AP (hostapd) Transfer speeds on Debian a maximum of 20Mbps/S. the Question is whether it is possible to achieve greater speed or so and have to work 802.11 g. (two card hold "g").
Reina asked October 10th 19 at 06:58
2
answers

Ubuntu hostapd wlan bridging

Why in Ubuntu 10.10 for a long time raises the connection bridge? /etc/interfaces auto br0<br> iface br0 inet static<br> address 192.168.0.1<br> netmask 255.255.255.0<br> network 192.168.0.0<br> bridge_ports eth0 wlan0<br> eth0 and wlan0 in the interfaces more not specified anywhe...
salvador.Hayes26 asked October 9th 19 at 18:15
3
answers

Speed local area network (hostapd+d-link dwa 547)

Good day to all! When setting up a home server there was a problem: the network speed does not exceed 10 Mbps. Is installed on the server card dwa 547 The new PC finds the network, connects to it and normally goes to Internet, but connection speed is displayed from 5 to 58 Mbps (300 I have not seen). Measured speed in a lo...
silas_Bailey54 asked October 8th 19 at 07:53
2
answers

USB WiFi for Linux/hostapd (802.11 n 300Mbit)

Did anyone raise 802.11 n access point using hostapd to 300Mbit? Advise USB adapter for this case, so there was less dancing. Like D-Link DWA-160 is assembled on ath and must be maintained
barry86 asked October 3rd 19 at 18:23
2
answers

Hostapd: simultaneous operation of two access points

There is a home debian servadac raised using hostapd access point. In /etc/default/hostapd is such a line: DAEMON_CONF="/etc/hostapd/hostapd.conf" In /etc/hostapd/hostapd.conf this: interface=wlan0 driver=nl80211 macaddr_acl=0 ssid=super-duper-point hw_mode=g ieee80211n=1 channel=6 ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40]...
chaya_Daugherty asked October 3rd 19 at 05:11
2
answers

How to configure Hostapd + Dhcpd for a pair of three clients?

Set up this subject with the configuration: hostapd.confinterface=wlan0 driver=nl80211 ssid=KPEBETKA channel=6 hw_mode=g auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_passphrase=vi776bnh wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP ctrl_interface_group=0 macaddr_acl=0 preamble=1 wmm_enabled=1 ieee80211n=1 ht_cap...
pascale3 asked September 30th 19 at 10:19
1
answer

Long pings on a wireless network hostapd

In fact, what we have:[kostett@localhost ~]$ ping -c 3 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_seq=1 ttl=64 time=1870 ms 64 bytes from 192.168.0.1: icmp_seq=2 ttl=64 time=1724 ms 64 bytes from 192.168.0.1: icmp_seq=3 ttl=64 time=1471 ms --- 192.168.0.1 ping statisti...
Erling.Blanda asked September 28th 19 at 01:29