Questions tagged [Juniper Networks] (53)

1
answer

ОМ2/OM3 compatibility?

Colleagues, welcome. Please help to understand the following question: Between floors in the building is laid optical fiber cable type 50/125 ОМ2. If I, for connectivity of network equipment between floors computerou patch Konami type OM3 50/125, still should work? Need it or ОМ2 patch cords? Thanks in advance.
1
answer

What would you recommend from routers?

There are 2 uplinks BGP on Cisco 6500, and one iBGP filter-machine (to show the page-the cover for the subscribers, who climb on the unwanted ILV sites). Today an excessive number of routes banging the cisk after receiving new routes for our valiant LV. Uplinks coming from the 680 and 690к routes respectively + around 140-1...
2
answers

In what could be the cause of the problem with the router Juniper SRX240H, if after switching on it does not load the OS?

After turning on the power button the router shows no signs of life other than the running fans. The fans start spinning at full capacity and do not pass into normal mode. Damage on the Board is not found. Also I would like to know the model of CPU/processor with this device, information on it can not be found on the websit...
Viola.Cruickshank62 asked April 1st 20 at 17:09
1
answer

Juniper ex2200 gibberish, how to fix?

Connected via Putty on the COM. Tried to change the port speed, character set. Cable normal, before 2 juniper connect.
kole_Schimmel asked March 29th 20 at 21:05
1
answer

What a concept Layer Supported?

Buy this unit and would like to know what the Layer is Supported and its value scatter for the beginner. Thank you https://junipershop.ru/switch-juniper/ex_series/ex... Specifically interested in the line Layer Supported - 3
Garnet69 asked March 23rd 20 at 18:37
1
answer

As the router Juniper EX2200 to switch typically the hub (switch)?

The old router Juniper EX2200, but no ordinary hub (or switch) to combine several machines in one network. Attention a question: how to do it with the help of juniper? just at factory settings to stick cables to the ports failed. tried multiple ports in one vlan to join, but also did not work, or not in that steppe has gone...
Bertrand_Eichmann asked March 16th 20 at 13:39
5
answers

Advise Cisk

Good day! More used to communicate with juniperum, but really I'm watching an analogue of Ciskowski glands, in order to decide on what to develop further. Suitable juniper EX3200-24T. From functional to critical is the support of BGP and to all of the ports were Gigabit. Prompt urgent (i.e. you can buy new, not UsedCisco) ...
vickie.Fer asked October 10th 19 at 07:07
3
answers

Specify where to dig: a single address space, 2 DC

So, what we have or will have in the near future: Its AS + PI network /24, and 2 or more data center equipment. Data centers in the same city and have good connectivity, but belong to different providers. What to get: a single address space to address .11 were in the same DC, and the address .12 in the other, if you wish, w...
vickie.Fer asked October 10th 19 at 01:20
2
answers

Can I clone mac on Juniper SSG-5?

Can I clone mac on Juniper SSG-5? As I can not find information...
Lonny.Cole asked October 10th 19 at 00:00
1
answer

Need Open-Source analogue Juniper ovskogo portal?

You need to publish some internal resources on a single IP, and that it was very secure. Wishes: 1. The client must have enough browsers to work. No flash drives and clients. 2. Everything should be encrypted in an adult. Know that adults can do a piece of iron, but I want to implement all at the open-sorce. Kick in the dir...
Terrence asked October 8th 19 at 02:19