Questions tagged [Raspbian] (121)

1
answer

How to configure routing from one ip:port to another ip?

All kind time of day. Faced with the problem of routing in Raspbian OS where you are trying to raise proxy (3proxy) using 4g modem. What is available: 1. Raspberry Raspbian OS installed c buster 2. There are 2 network interface wlan0(192.168.1.100) is Wi-Fi with full access to the network and eth1(192.168.10.100) 4g modem...
jayson12 asked April 18th 20 at 13:08
1
answer

You cannot customize the output in the Internet through the mobile proxy 3proxy?

Can't get online through the mobile proxy, the manual seems clear, collected the file configs, start 3proxy, but when pointing the browser gives kabud, then the proxy is not available, logs attached. 1. Data networks (dedicated seteviki which use wlan0 - basic connection, eth1 is the modem) 2. File 3proxy.cfg 3. Log file ...
miles.Kunze asked April 9th 20 at 10:53
1
answer

How to configure bridge mode on the Raspberry Pi?

Hello, colleagues! Really need your help in setting up a network on the Raspberry Pi. Have: 1. The Raspberry Pi Is A Zero Of W; 2. LTE USB modem Huawei E3372h with the advanced web interface; 3. SIM card with a white ip address (which is white, from the Internet pinged quietly) 4. Web application written in Flask. As the s...
annabell_McLaughlin asked April 9th 20 at 10:01
1
answer

How to make a Raspberry pi 3b, wi-fi to operate at 40 Mhz?

Hello! In Linux the stump, because asking for Your help. So. A piece of Raspberry pi 3b, with Raspbian Buster on Board. Piece of hardware connected to the network via wi-fi. Have a router MikroTik mini hAP, which exhibits mode wi-fi G/N/20-40Mhz. So, the first problem was that max speed does not exceed 56 Mbps. Solved it re...
casey asked April 8th 20 at 10:19
1
answer

Virtual environment does not see Django, how to fix?

when the command is python manage.py runserver error A virtual environment is enabled, Django is installed
Terrence.Brown asked April 8th 20 at 09:50
1
answer

As Zero on the Raspberry Pi to use hardware PWM for sugovica?

Stepper motor(Nema17) connected to the Raspberry pi using Zero driver a4988. I need to submit a certain number of pulses on a pin with more or less the exact frequency. Software Malinka generates the pulses unstable. I understand there need a hardware PWM or proiperty through a DMA, etc. Tell me any working solution for the...
leil asked April 7th 20 at 11:54
3
answers

Why not go packets in Raspberry Pi AP?

Welcome. Did everything according to instructions. It works, addresses for DHCP clients are assigned, but not ping none of the host of the raspberries and the client.
1
answer

How to run proxy on the raspberry?

Few understand the proxy configuration, therefore, appeal to knowledgeable people :) Iron: Is a Raspberry pi3 (Raspbian/Debian) with glued to it using USB modem (ppp0), the Raspberry itself is connected via Packard to a WIFI home router with the Internet. To control the Raspberry use VNS. If you turn off the Internet modem...
doris_Legros18 asked April 7th 20 at 09:09
1
answer

Where the files vmlinuz and initrd.img raspbian buster?

Need these files for remote download but in /boot they are not
Andreanne_Zula asked April 4th 20 at 14:15
2
answers

The Raspberry pi does not boot until I touch the arm GPIO 14 or 15 (UART)?

Raspbery pi 4 is not activated and does not restart until you touch the arm GPIO 14 or 15 - actually this question. When you turn on or reboot the red led is on and that's it. Just touch your finger to the side of the comb gpio - blinking green and go download... tested on 2 PSU - the situation is similar.
madisen_Howell asked April 4th 20 at 12:52