Questions tagged [ZyXEL] (138)

3
answers

How to organize a network with 2 firewalls?

Hi, please advice: There are 2 Firewall - DryTech Vigor 2925 and Zyxel USG60W and switch. Need to connect the network with the max protection which scheme is better to make? Your options?
broderick74 asked April 4th 20 at 13:17
0
answer

Selection of unique network equipment. Help?

Good time of day. Please help me with searching of analogues of equipment : - Radware Alteon 5208-6G - Fortigate 100E - Alcatel OS99-GNI-U48 - Alcatel OS99-GNI-48 - Alcatel OS9907-RCB-A - Alcatel OAW-AP1101-RW - Alcatel OV4-START-NEW - Alcatel OV-NM-EX-100-N I would like to collect it all from the same manufacturer (Cisco, ...
claudine_Walt asked April 2nd 20 at 15:29
2
answers

Marshrutizator — "the patient is alive or dead"?

marshrutizator Zyxel Kennetic Giga, firmware from 2015 (latest) - Firmware-Keenetic-Giga-2.04[USD.2]C7 Worked fine all the years from the date of purchase, if the Internet was "off", the problem has always been on the provider side. Until today....Morning came off the Internet (my local time), left the application, the oper...
Modesta.Nicol asked April 1st 20 at 17:29
3
answers

How to configure VLAN on the Zyxel GS1900-48?

There is a managed switch Zyxel GS1900-48. It connected end-users (computers), router Dlink DIR-615, through him we get access to the Internet, and 3 unmanaged switch. How to configure VLANs so that users sitting on the unmanaged switch, 48 port GS1900-48 had the Internet router 8 port GS1900-48, but did not have access to ...
Sydney19 asked April 1st 20 at 16:19
2
answers

Why falls off Wi-Fi when connected to any Ethernet port on the router Kinetic Giga?

Hi! Routers have this brand at work, at home and at relatives. Last summer the problems started. Stick the cable from your computer to any port of the router and immediately lost Wi-Fi. On the router the wireless diode is blinking randomly. Before these problems arose. The router was set up 3 years ago. Reboot does not help...
marielle_Terry asked April 1st 20 at 15:29
1
answer

How to set a route for a single segment and put it on the vpn?

Good afternoon. A Zyxel Ultra, on it 2 network segment: 192.168.1.0 and is 192.168.88.0. Raised to own L2tp vpn server. Task - all traffic is 192.168.88.0 to put on L2tp. How to register a static route?
sarina asked March 29th 20 at 20:25
0
answer

How to put some clients on Keenetic using Raspberry with ExpressVPN?

Good day! Raspberry have installed ExpressVPN. In the LAN of the customers (hang through the hub on one port Keenetic Ultra) should be allowed only through VPN from RB. The remaining clients can go to Internet directly without VPN. Is it even realistic to implement?
brisa77 asked March 27th 20 at 13:43
4
answers

How to place the router/routers in the apartment?

Good day, there was such a "dilemma." There is a two-bedroom apartment with an area of 60 sq m, with a distinctive layout, have keenetic giga the latest in white casing. I wish the apartment was confidence in a 2.4 GHz network, and of course, 5GHz network. In the picture that is attached you see 2 options: 1) have the main ...
norene.Ullri asked March 27th 20 at 11:32
0
answer

What a strange log entries?

Good afternoon. Every minute in the log zyxel keenetik lite 2 appear these records: Aug 2 01:12:40 nimproxy sendmsg() failed (network is unreachable). Aug 2 01:12:40 nimproxy failed to send igmp interface packet to ra2. Aug 2 01:12:40 nimproxy sendmsg() failed (network is unreachable). Aug 2 01:12:40 nimproxy failed to send...
dorthy_Buckrid asked March 25th 20 at 12:56
1
answer

Access street access point of another network via VPN?

Have configured VPN network: 1) 192.168.1.* router Keenetic Giga (KN-1010) - permanent IP raised the VPN server L2TP 2) 192.168.2.* router Keenetic Giga II - client - connected via a 4G modem The channel is configured in both directions with static routes. The client device is connected to TP-LINK TL-WA5210G - connected a...
mary63 asked March 25th 20 at 11:48